-
Who this checklist is for (and what it won't cover)
-
Step 1: Map the space before you call a single vendor
-
Step 2: Keep the vacuum and the ventilation in separate RFQs
-
Step 3: Force every quote into the same line-item format
-
Step 4: Make the vendor prove the 'strongest central vacuum' claim
-
Step 5: Lock the rough-in before the drywall goes up
-
Step 6: Size the heat recovery system on airflow, not floor area
-
Step 7: Test, document, and hold retainage
-
Step 1: Map the space before you call a single vendor
-
Common mistakes that cost real money
Who this checklist is for (and what it won't cover)
I'm the office administrator for a 220-person company. I handle facilities and vendor purchasing—roughly $180,000 a year across 11 vendors—and I report to both operations and finance. In 2024 we consolidated three offices into one 4,800-square-foot floor, which is how I ended up owning procurement for a central vac vacuum, a heat recovery system, and everything in between.
This is the seven-step checklist I use now. It assumes you already know you need ventilation, a built-in vacuum, or both, and that you're the person who has to get comparable bids, keep the project on schedule, and survive the invoice audit afterward. It won't tell you how to size ductwork—that's your mechanical engineer's job.
Step 1: Map the space before you call a single vendor
Before quotes, build a one-page document: room list with square footage, how many vacuum inlets you think you need and where, where the power unit can live (garage, mechanical room, loading dock—it needs power and either an exterior exhaust or a filtered return), and whether each restroom or the break room has an exterior wall available for ventilation equipment.
Here's the mistake I made early on. In my first year handling this, I made the classic specification error: I assumed 'standard inlet spacing' meant the same thing to every vendor. On a 4,800-square-foot floor, one contractor proposed five inlets, another proposed nine, and a third asked where the hose would be stored—a question I hadn't considered at all. I'd already told my VP the bids were apples to apples. They weren't, and re-quoting cost us a week.
Checkpoint: you can send an unnamed floor plan with numbered inlet locations and get back bids you can actually compare.
Step 2: Keep the vacuum and the ventilation in separate RFQs
These are two different trades on two different schedules, and bundling them is how you get one badly priced line item that nobody questions.
A central vacuum is dust and debris removal—tubing in the walls, valves, a power unit, sometimes an exterior exhaust. Heat recovery ventilation is fresh air: it brings outside air in, exhausts stale air out, and transfers heat between the two streams so you're not throwing your HVAC budget out the window. If you only need one problem room fixed, a single room heat recovery fan (through-wall, one unit, one small room) is a very different purchase from a whole-floor heat recovery system.
I've seen both lumped into a single 'mechanical' quote more than once. The vendor wins, and the comparison loses.
Step 3: Force every quote into the same line-item format
When someone asks about the cost of a built in vacuum system, the honest answer is that it depends entirely on what's in the quote. Require a breakdown:
- Power unit make and model, plus filtration type
- Tubing footage and material
- Number and type of inlets/valves
- Installation labor
- Electrical rough-in (usually a separate electrician—ask who's paying)
- Drywall patching and paint after rough-in
- Accessories: hose length, tool kit, garage or utility inlet
Our three February 2026 bids for a six-inlet system came in roughly $1,900 to $3,600 installed. The spread was almost entirely labor and whether electrical was included. Don't hold me to those figures as market rates—get your own three bids in writing—but the pattern holds: the low bid was low because it excluded two things.
We also moved this process into a shared vendor folder in 2025. Submittals, quotes, and certificates all land in one place, and our AP team can pull documents without emailing me. That cut my review time per bid from about 40 minutes to 15, and it eliminated the missing-W-9 problem we used to have every quarter. Fewer manual handoffs, fewer errors—on both sides of the transaction.
Step 4: Make the vendor prove the 'strongest central vacuum' claim
This is the step almost everyone skips, and it's the one that determines whether you actually got what you paid for.
Ask for three numbers: sealed suction (water lift, in inches), airflow (CFM) measured at the working inlet, and air watts. Marketing sheets love peak values measured at the power unit with nothing attached. A unit rated at the canister tests very differently at the end of 40 feet of tubing and a 30-foot hose.
Ask for the third-party test report and the test conditions it was run under. If a vendor can't produce one, that tells you something. As of April 2026, this is still the fastest way I've found to separate real spec sheets from adjectives.
Per FTC advertising guidance (ftc.gov), performance claims must be truthful, not misleading, and substantiated with evidence. 'Strongest' is a performance claim—not a description.
I went back and forth between a cyclonic unit and a bagged unit for about two weeks. Cyclonic meant no bags to buy, ever; the bagged unit had a filtration rating I could hand to our safety lead and easier service access. I chose the bagged unit, because our maintenance staff would rather have a known filter part number than a filtration claim that's hard to verify.
Step 5: Lock the rough-in before the drywall goes up
Built in wall vacuum systems live or die on rough-in timing. Once drywall is closed, every change becomes a cut-and-patch job that shows up in your punch list and your budget.
What to verify before the board goes up:
- Valve boxes secured to studs, level, at a consistent height
- Tubing supported along runs, with gentle bends—sharp elbows kill airflow
- Low-voltage wire run to every inlet and back to the power unit location
- Power and exhaust provisions at the unit location
- Photos of every wall cavity, labeled by room
In my opinion, paying for a rough-in inspection before drywall is the single best few hundred dollars in this entire project. Looking back, I should have written it into the original scope rather than adding it as an extra—at the time, I assumed it was implied. It wasn't.
Step 6: Size the heat recovery system on airflow, not floor area
For a heat recovery system, the spec that matters is certified airflow at your design static pressure—not 'covers up to X square feet.' Get a room-by-room airflow calculation, and confirm:
- Frost control strategy for your climate (defrost cycle, preheater, or recirculation)
- Filter access—if changing filters means pulling a panel in a cramped closet, it won't get done
- Controls: who sets the schedule, and whether facilities can override it
- Who commissions and balances the system, and what report you receive
If a single room heat recovery fan is the actual answer—one restroom, one break room—check the wall assembly first. Through-wall units need a sleeve, a clear exterior location for the grille, and a condensate plan in cold weather. That's the detail contractors tend to leave for installation day.
Step 7: Test, document, and hold retainage
Don't release final payment on the strength of a walkthrough. Hold 10% until you have:
- A suction reading at the farthest inlet, compared against the spec you were quoted
- Every inlet checked for leaks and proper seal
- Documented airflow balancing on the ventilation side
- Frost control tested, not just described
- O&M manuals, filter part numbers, and warranty registration confirmed
I still kick myself for releasing final payment on our first phase before the commissioning report arrived. Two dampers were stuck. Because the money was already gone, I spent six weeks chasing a callback instead of pointing at a retainage line.
Common mistakes that cost real money
- Not verifying invoicing capability up front. Years ago I found a great price from a new vendor and ordered without checking how they billed. Handwritten receipt only. Finance rejected the expense report and I ate $2,400 out of my own department budget. Now I confirm the PO and invoicing process before any order goes out—no exceptions.
- Buying the 'strongest' unit based on marketing numbers. Peak ratings don't clean floors.
- Bundling vacuum and ventilation into one quote. You lose the ability to compare anything.
- Missing the rough-in window. Retrofit costs roughly three times what pre-drywall work does—at least, that's been my experience on two projects.
- Forgetting consumables. Bags, filters, and belts are a recurring line item. Ask for part numbers and prices before you sign.
- Skipping commissioning. An unbalanced ventilation system is an expensive box that makes noise.
One last thing. This checklist is built around a 4,800-square-foot office with fairly standard requirements. That said, if you're specifying for a building over roughly 10,000 square feet, or a space with unusual occupancy, get a mechanical engineer to stamp the ventilation design. The vacuum side scales predictably. The ventilation side does not.